Cider

2009-11-30

After the first snow had fallen, me and my colleague Fumi were given permission to pick the apples of the botanical garden at our university. There were about 30 kg of them. That yielded 14 half a litre bottles of cider (batch 2009/1). I used a centrifuge-type juicer from Lidl, but it died after about 10 kg of apples, the rest were juiced with a steam juicer (Mehu-Maija). Juice from the centrifuge was significantly better tasting. The cider turned out pretty good, but had a nasty taste of yeast or homemade alcohol. Perhaps because it was brewed in room temperature (21-22 °C) . Next time I'll try the refrigerator (7-8 °C). The alcohol content was 5.4 % from the sugar of the apples alone. Inspired by the moderate success, I started to think of a better way to juice, and found some nice "apple scratter" videos from youtube, and building instructions from web. I bought some supplies:

  • Wooden rolling pin, 3.5 EUR
  • 230 V hammer drill, 10 EUR
  • 12 V cordless drill, 15 EUR
  • 200 pcs of 30 mm stainless steel nails, 12 EUR

Total: 40.5 EUR.

I also used:

  • Plywood, MDF, lumber (all dumpster-dived)
  • A croquet mallet (from my father, who had bought a set for its strong wood), for the shaft
  • 10 mm iron shaft, for connecting the wooden shaft to the drill chuck.
  • A piece of copper tube, glued and bolted around the connection of the iron and wood shafts to prevent the wood from splitting.
  • Wood glue and Araldite glue
  • Screws, a bolt and a nut
  • Power switch (for changing rotation direction)

The drills:

drills

I demolished them. This is what was left after removing the goodies:

drills2

I proceeded to build a motor for the scratter, using the gear from the hammer drill and the motor and transmission from the cordless drill:

scratter motor

I also recycled the female DC connector from the battery charger. I have a regulated 70 W 12 V DC power supply, which I use to run the motor. It was not intended for use with motors or any other device that draws a lot of current to start. An over-current protection switches on whenever the current goes too high. The scratter had difficulties starting, especially after a jam. So I built a "booster" from three LiIon batteries in series (from a dead laptop battery, 10,8 V in total), connectable parallel to the scratter by a push button or by a switch for charging. It helps the power supply to start, and helps when there is much resistance to torque. The motor is very powerful, does not heat much, and the rotation speed is just right. It makes noise, but not too loud. During the process, I found the potential weak spots in the construction, to which special attention should be paid:

  1. The shafts that attach to the chucks must be filed triangular in order to prevent slippage.
  2. Rotation of the cordless drill motor enclosure must be prevented properly.
  3. It must be ensured that the gears from the hammer drill stay in contact. They have a tendency to jump if they have a chance, and can be ruined in the process. So attach everything firmly in place.

I used this kind of a screw pattern in the roller:

screwpattern

Here is the scratter in action:

Some thoughts:

The diameter of the rolling pin is not large enough. The apples don't like that the passage goes so narrow so fast. But assisted with a plank, in the apples go. After relieving my right hand from its cinematographic duties, things progressed much faster than in the video.

Yield is around 50 % w/w juice, when pressed with a 150 EUR Palumbo 4.5 L press (from Myllyposti) that I co-own with another work mate of mine, Silke.

I sampled the (imported) apple varieties that are sold locally here in Oulu. Expensive! The most suitable one for cider making was Granny Smith, costs about 1.50 EUR/kg. Cheap polish apples, 0.50 EUR/kg, were no good as they lacked the crispy, acidic taste. The second best was Jonagold, 1.30 EUR/kg or so.

2009-12-02

I bought 41 kg of Granny Smith apples from Prisma at 1.40 EUR/kg, but got a discount and they also made some mistake in the weighing (to my advantage), so I paid only for 22 kg. Thanks to Marjo for helping out with a car.

I scratted the apples and pressed them. That took 2 ½ hours, not including cleaning up. The scratter worked well and atomized at best 4 apples per minute. The screw pattern I had used on the roller worked wonders, always leading the apple to the middle. I ended up processing one apple at a time, sometimes two.

I got about 23 L of juice. The price of the juice turned out 1.30 EUR/L, only half of what I had been prepared for. The taste was really nice and crispy (sour, tart), not exceedingly sweet though. I think the cider will be excellent with food if it turns out successful.

Some pictures of the action:

juicemaking scratteraction scratter waste

I divided the juice into two times 10 L parts for making cider, let's call them batches 2009/2 and 2009/2k where k stands for cooked (keitetty). This will be a comparative experiment to find out whether the juice should be cooked, which also sterilizes it. To both batches I added 2.5 ml of brewer's salt. I cooked batch 2009/2k until it boiled, and then let it to cool. I added 0.5 ml of wine yeast to batch 2009/2 and put it on the top shelf of the refrigerator, which is at 7-8 °C. Tasting the yeast, I recognized the bad taste from batch 2009/1. That's why the minimal amount of yeast this time. It might be a good idea to do what some people do if the bad taste is in the dry yeast: cultivate some yeast (with sugar?) and use that instead of dry yeast.

Have to remember to add yeast to batch 2009/2k tomorrow, when it has cooled. (I did.)

Having tasted the juice now a few times, I'm starting to think that maybe it was even too sour. Mixing in some other apples might have been a good idea. Time will tell!

2009-12-04

I measured the sugar content of the juice using a hydrometer, the result was +50 degrees Oechsle, or 50 °Oe * 2.5 g / L / °Oe = 125 g/L of sugar. If all sugar is fermented, that should give 125 g / L / (17 g / L / %) = 7.4 % alcohol by volume. Whoa! I guess I was wrong about the juice not being that sweet. Must've been all the acidity.

2009-12-14

The bucket 2009/2 was leaking somehow, so I moved both batches 2009/2 and 2009/2k into new buckets, at the same time trying to avoid pouring the sediment at the bottom into the new container. From the taste, it seemed there was already at least some fermentation going on, but not much alcohol yet.

2009-12-26

I tasted 2009/2k, it was definitely fermenting. It was bubbly. But still very sweet. No bad taste, which is a good sign.

2009-12-29

I tasted 2009/2. Was the same as 2009/2k. No peculiarities in the taste, so it seems pasteurization was not necessary (note: later, this conclusion will be shown to be incorrect...) .

2010-01-26

Batch 2009/2  had fermented further than 2009/2k. Also, it was less cloudy, more yellow and had a somewhat sulfurous, rotten stench. So, pasteurization is good, after all. I liked the batch 2009/2k more. I hope tasting 2009/2 won't give me stomach problems. (No stomach problems ensued.)

2010-02-08

Tasted 2009/2k, was good, and quite sweet still, and bubbly, so it is still fermenting.

2010-02-19

Tasted 2009/2k, it was good. The sweetness was now less, meaning that fermentation is approaching the finishing line...

2010-03-26

Tasted 2009/2k, the sweetness was now about right for cider, there was a somewhat dry taste emerging. Transferred to another bucket, stopped fermentation by adding sulfite, and also added a clarification agent. Shook, and left in the refrigerator to clarify. There was plenty of carbon dioxide. On the next day, added the second clarification agent.

2010-04-02

Bottled and carbonated the cider. It turned out pretty good! Plenty of acidity, could be a slight bit less. Sweetness was quite ideal. This is not a dry cider. Hydrometer reading was +20 degrees Oechsle, which is 30 °Oe less than in the beginning, corresponding to 4.4 vol% alcohol, according to my calculations. An on-line fermentation calculator gave a different estimate, 4.1 vol%, which is, by taste (and by the level of induced intoxication), closer to the truth. The dreaded yeast taste that I wanted to avoid was minimal, but still there somewhere. For the next batch (if I shall make one) I would use the sediment from a previous fermentation, to get rid of the dry yeast taste. I have now saved some of the sediment, in the refrigerator. Also, I would try to avoid tasting the cider while it is fermenting. Now I know that with these parameters it takes about 4 months to finish. The final yield was 14 half-a-liter bottles, or 7 L of cider. I would not hesitate to try this with something like smoked salmon salad. I'm quite happy that I did not add any extra sugar, it is all from the apples

2010-04-14

I have started another batch, but could not use yeast from the last batch. It had turned into vinegar... So I simply used 0.5 ml of dry yeast per 10 L bucket. An interesting thing to note is that Granny Smith apples bought early in the spring yielded less juice (less than 50 % by weight) than "new ones" in the autumn. I guess they are slowly drying. Also, they did not appear as sour. These might be positive things for the quality of the cider, but also increase the cost. I'm not absolutely sure how sweetness was affected, so I'd better not comment on that.

2010-05-05

Here is the cider making process that I have used, with some additional observations:

  1. Disinfect, disinfect, disinfect. You must work cleanly, or the risk of contamination will be something like 75 %. Especially if you don't use much yeast in the beginning. And you don't want to use much yeast, because that will affect the taste as well.
  2. Get some apples. 2 kg of apples will give 1 L of juice. Sour apples are better, like Granny Smith or local varieties. Bitter apples are also a good addition, as they give more taste of the cider. These are not sold in supermarkets, but can perhaps be found locally. Small garden apples are often bitter. It is also good if the apples have plenty of sugar, as that will give a stronger cider. You can mix a few varieties to get the best of all worlds. It is OK if the apples have darker spots and bumps, as this will only contribute to the authentic "slightly rotten" cider flavor.
  3. Wash the apples, to get rid of dirt on the surface. Use a disinfectant to reduce the risk of contamination.
  4. Grind the apples into pulp. For this you can build a scratter similar to what I have. Because my scratter does not automatically suck in the apple, but requires me to assist with a plank, I found it the easiest to grind one apple at a time. No need to peel the apples or to remove seeds, as they are so dry that not much juice comes out of them to affect the quality of the cider. Do not allow the pulp to aerate too much, work in smaller batches (the size of the apple press) and press them immediately after scratting.
  5. Press the juice out of the pulp using an apple press. If the press has a sieve, then you don't need to use a cloth, but it will anyhow make it easier to remove the dry pulp from the press, and it keeps the sieve clean. Any cloth that is clean should do, but be aware that an older cloth might rip in the process, so have a spare one ready. Discard the dry pulp as bio-waste.
  6. Measure the specific gravity of the juice using a hydrometer. This will tell you the sugar content, which can be used for estimating the amount of alcohol when compared to the sugar content after fermentation. If there's not enough sugar, you can add some. The cider, when ready and bottled, should be about 20 °Oe (or a bit less for a dryer cider), so if you are not going to add sugar afterwards, you need about 50 °Oe now to get at least 4.4 vol% of alcohol.
  7. Boil the juice. There will be some foam forming on top. It can be removed using a small sieve. Boil properly; you don't want any bacteria to survive. You could also try boiling a small amount separately until it thickens and gets a nice caramel aroma, and then add to the main batch.
  8. Pour the juice into the fermentation container while it is still hot. The fermentation container should have a one-way valve on top of it. You can use one of those air locks that have water in them. I find it adequate to have a hole in the lid and a piece of plastic bag taped on it. Seal the sides of the lid carefully. For a long fermentation it may be sensible to use adhesive tape for extra sealing.
  9. Let the juice cool down to room temperature overnight or longer, depending on the size of the batch.
  10. Buy a wine kit that is intended for a longer fermentation, not one of those 48 h kits. All the further ingredients will be from the kit. The wine kit will also have a sheet of instructions and it will be good to follow them, to the extent that they are compatible with the cider making process.
  11. Add 0.5 ml of the dry yeast / 10 L of cider, and 2.5 ml of brewer's salt / 10 L of cider and mix. The smaller the amount of yeast, the better, as dry yeast has a bad taste. It will be a better idea to grow some yeast beforehand and use a part of that. It will have less of the original bad taste. Brewer's salt provides nutrients for the yeast, enabling it to grow faster and longer. The yeast will not produce alcohol or carbon dioxide if it is not growing. It is incapable of "wasting energy". I'm now experimenting if the yeast grows long enough without the salt.
  12. Ferment the cider for 4 months at 8 °C. If you have a different temperature, then things might progress faster (warmer) or slower (colder). I use the upper shelf of the refrigerator, and it just so happens to be at that temperature. I'm quite sure a shorter fermentation in a warmer temperature would be OK, but don't have it above 16 °C.
  13. Follow the instructions of the wine kit for the clarification step, but keep the cider refrigerated during the process. You can allow the clarification to continue for a couple of extra days to get a cider free of floating gunk. After clarification, the yeast will be dead and forms a sediment on the bottom of the fermentation container.
  14. Have a taste and decide whether you want to add sugar to sweeten the cider or not. If you do sweeten the cider, use a sugar solution instead of crystalline sugar, as it will be hard to dissolve the sugar into cold cider. Measure the specific gravity for your notes.
  15. Use a siphon to bottle the cider. Carbonate the cider using  a carbon dioxide tank, a pressure reducer and a bottle cap adapter. You can use a larger bottle first, allow the carbon dioxide to dissolve for an hour or so, and then pour the cider into the final bottles.
  16. The cider will be ready for drinking. Enjoy! Storage of a couple of weeks may improve the taste. I keep my cider refrigerated at all times.

2010-09-28

Started making another batch of cider with my friend Nelli. Her boyfriend Timo has a temperature-controlled cabin for making beer, and we are using that, set at 12 °C. We bought 20 kg of golden delicious apples and added about 30 kg of local apples of different "decorative" varieties to add taste and sourness. We juiced the apples with my scratter and juice press, and cooked the juice, added 10 ml of brewer's salt and poured into the fermentation container, with a total volume of juice at 17 L. The juice measured 50 °Oe. On the previous day (2010-09-27) we had started a starter by adding 1 ml of dry yeast into 2 dL of sterilized granny smith juice at room temperature with the equivalent of 2.5 ml of brewer's salt / 10 L of juice. The starter was then immediately mixed and moved to 12 °C.

2010-09-29

Moved the container from room temperature to 12 °C and added 1 dl of the starter.

2011-01-11

CONTAMINATION! Bad luck. The cider got a bad smell, dark color and an off taste. Had to throw all of it away.  Have to sterilize better in the future! I have updated the instructions accordingly.

8 thoughts on “Cider”

  1. Great blog. Really helpful to share axperiences as I’m new to all this and trying to learn as much as I can.

    Just one question…..

    When you added the final sugar solution to sweeten it after fermentation, how much water did you dissolve the sugar into ?

    I have found with my first attempt this year, that my cider has come out very “thick” (almost the thickness of used engine oil). It tastes nice enough but is MUCH thicker than it should be.
    I am wondering if I should have made my final sweetening sugar aolution a little thinner (i.e. more water content) before I added it, but I can’t find anywhere that specifies how much water to mix the sugar into before adding it to the cider.

    Would really appreciate any advice. Many thanks.

  2. Neal, I didn’t add any “artificial” sugar, but stopped fermentation at the point when the sugar content was about right. The wine kit has some stuff that kills the yeast. Then artificial carbonation.

    I wonder, if it’s very sweet if it’s that thick. Or if something else than sugar is causing it.

  3. Why don’t you use bought apple juice directly? In a nearby Spar it sells for 21¢ per litre.
    I know an acquaintance once made cider mixing bought apple juice, plain white sugar and yeast. It was fantastic! 8D

  4. Doug, yeah that should work. But the cheap stuff is made from concentrate, so it won’t be up to my high standards… :–) Valio has some really nice pressed organic apple juice, but it’s super expensive.

  5. Wow, I read through the whole thing, you have a lot of info here.
    Would love to try to make cider sometime. Would love to try pear but am not sure if it would work the same way as apples do?

    1. Dear Mossycoat, my brother tried with pears, and I think it worked just the same. You can taste the juice beforehand to judge if it’s acidic enough. If not, you could add citric acid or juice from tart apples such as some of the smaller decorative apples. I’ve had bacterial contamination take over my cider batch a couple of times. To prevent that, you can add Campden tablets before fermentation.

  6. I’ve made “cider” using supermarket apple juice and honey (for sugar->extra alcohol) a couple of times, the first few times I simply used supermarket bread yeast. Yes. It does have a weird aftertaste (so I used proper wine yeasts after that), however if you have the patience, that taste *will* go away if you let it ago for another month or two (plus decanting it once or twice to get rid of the sediments).

    The advantage is if you use more yeast, you won’t have to worry about contamination as much, because the yeast will fight the other organisms (somehow). I used (very dilute) bleach solution and triple water rinsing for desinfection, and in general that works. I guess it helps to be easier on this if acquiring the juice is much easier and a wasted batch is not a waste of so much effort.

    Thanks to the honey I got much higher alcohol percentages (must have been 13-15%, judging from intoxication and taste).

    One other thing. You will love this, if you ever get a batch that just doesn’t taste very “interesting” or flavourful. Look up “applejack” on Wikipedia. Or “freeze destillation”. I figured out a brilliant method: Freeze your cider (the colder the better). You will get a yellow-orange cider “slush puppie”. Scoop this into a big *salad spinner*, the sides of which you have covered with paper kitchen towel. Don’t fill it more than 1/3rd because salad spinners weren’t really made for this work and it will break otherwise. Spin. The slush will turn white, like cheap popsicle. The liquid outside will be bright yellow-orange, concentrated in alcohol, sugar and flavour. For some reason, most “off” flavours tend to stay in the white ice that you throw away. The colder you freeze, the more concentrated it gets. According to some chart I found on the Internet, my standard home freezer of -18 degrees Celsius would be able to attain somewhere between 20-25 percents of alcohol! And it tastes really nice, a bit like Apfelkorn (though that is not made by freeze destillation).

Leave a Reply to Olli Niemitalo Cancel reply

Your email address will not be published. Required fields are marked *